|
1. Install the camshaft regulator. For this purpose fasten a flange shaft (16) new bolts (T40 wrench size). Tighten bolts as follows: at first a dynamometer key with m 20 N.' moment, then Rozhkov a key tighten for 90 ° (1/4 turns). |
| 2. Turning to the left, spread a gear wheel of the inlet camshaft (13) with the adjusting piston (14) and a spherical spring (14a), at the same time it will enter gearing with a flange shaft. The position of a flange shaft should be set previously. The markings put with paint have to coincide. |
| 3. Impose the operating chain on a gear wheel of the inlet camshaft. At the same time the markings put during dismantle on the operating chain and a chain wheel have to coincide. |
| 4. Tighten a nut (6) with m 65 N.' moment, at the same time lock vents it has to be directed outside. |
| 5. Insert an anchor (2), at the same time the tightening plug on an anchor has to be over obtusion of the operating piston (18). |
| 6. Tighten a bolt with a fillet (1) as follows: a dynamometer key with m 5 N.' moment, then tighten in the same direction on 90 ° (1/4 turns). At the same time hold an anchor (2) for lysk with Rozhkov SW24 key. |
| 7. Fasten a gear wheel of the final camshaft, and for the l engine 1,8 / 2,0 – in addition a gear wheel of an inlet shaft with the imposed new bolts (T40 key size) operating a chain. Markings on a chain wheel and a chain have to coincide. Tighten bolts as follows: a dynamometer key with m 20 N.' moment, then tighten in the same direction Rozhkov a key on 90 ° (1/4 turns). |
8. Establish a natyazhitel of a chain.
Prevention
Extend lock pins from camshafts.
|
| 9. Connect an exhaust pipe. |
| 10. Put on a hose of cooling liquid behind a head of the block of cylinders and record hose clips. |
| 11. Screw the directing tubes of measuring instruments of level of oil of the engine and the automatic transmission on a head of the block of cylinders. |
|
12. Cover sealing surfaces of a forward cover (23) heads of a side of cylinders with sealant 002 989 0020 10 or other sealant. |
| 13. Install unloading plugs for two bolts (1) (diameter of a carving of 8 mm) behind a cover. 56. Establish a new sealing ring of round section for cooling liquid and insert a cover. |
| 14. Screw bolts (1) on both sides with m 20 N.' moment, and bolts (2) (diameter of a carving of 6 mm) with m 10 N.' moment. |
| 15. Establish a wire a lambda probe. |
| 16. Put on hoses for removal of air a head of the block of cylinders. |
| 17. Screw the holder of the position sensor of the crankshaft behind a head of the block of cylinders. |
| 18. Screw an inlet collector on a head of the block of cylinders. |
| 19. Establish new sealing laying, tighten bolts evenly cross-wise with m 20 N.' moment. |
| 20. Install the regulator of cooling liquid (thermostat). |
| 21. Fill in cooling liquid. |
| 22. Establish a cover of a head of the block of cylinders. |
| 23. Connect a wire of "mass" of the accumulator. |
| 24. Expose time on hours. |
| 25. Enter an anticreeping code of radio. |
26. Warm up the engine up to the working temperature and check for tightness.
Prevention
At leak of oil because of leakage of sealing laying of a head of the block of cylinders oil replacement is recommended.
|